manualshive.com logo in svg

Agilent Technologies 2000 X-Series, User Manual

Share
Download
Agilent Technologies 2000 X-Series User Manual Download Page 300

300

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

23

CAN/LIN Triggering and Serial Decode

 

5

Press 

Source

; then, select the channel for the CAN signal.

The label for the CAN source channel is automatically set.

6

Press the 

Threshold

 softkey; then, turn the Entry knob to select the CAN 

signal threshold voltage level.

The threshold voltage level is used in decoding, and it will become the 
trigger level when the trigger type is set to the selected serial decode 
slot.

7

Press the 

Baud

 softkey; then, turn the Entry knob to select the baud 

rate that matches match your CAN bus signal.

The CAN baud rate can be set to predefined baud rates from 10 kb/s 
up to 5 Mb/s or a user- defined baud rate from 10.0 kb/s to 4 Mb/s in 
increments of 100 b/s. Fractional user- defined baud rates between 
4 Mb/s and 5 Mb/s are not allowed.

The default baud rate is 125 kb/s

If none of the pre- defined selections match your CAN bus signal, select 

User Defined

; then, press the 

User Baud

 softkey and turn the Entry knob 

to enter the baud rate.

8

Press the 

Sample Point

 softkey; then, turn the Entry knob to select the 

point between phase segments 1 and 2 where the state of the bus is 
measured. This controls the point within the bit's time where the bit 
value is captured.

9

Press the 

Signal

 softkey and select the type and polarity of the CAN 

signal. This also automatically sets the channel label for the source 
channel.

•

CAN_H

 — The actual CAN_H differential bus.

•

Differential (H-L)

 — The CAN differential bus signals connected to an 

analog source channel using a differential probe. Connect the probe's 
positive lead to the dominant- high CAN signal (CAN_H) and connect 
the negative lead to the dominant- low CAN signal (CAN_L).

60%

70%

80%

Sample Point

One Bit

Summary of Contents for 2000 X-Series

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands