manualshive.com logo in svg

Agilent Technologies 2000 X-Series, User Manual

Share
Download
Agilent Technologies 2000 X-Series User Manual Download Page 197

Measurements

14

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

197

 

1

From the Measurement Menu, press the 

Settings

 softkey; then, press the 

Thresholds

 softkey to set analog channel measurement thresholds.

You can also open the Measurement Threshold Menu by pressing 

[Analyze] > Features

 and then selecting 

Measurement Thresholds

.

2

Press the 

Source

 softkey to select the analog channel or math waveform 

source for which you want to change measurement thresholds.

Each analog channel and the math waveform can be assigned unique 
threshold values.

3

Press the 

Type

 softkey to set the measurement threshold to 

%

 

(percentage of Top and Base value) or to 

Absolute

 (absolute value).

•

Percentage thresholds can be set from 5% to 95%.

•

The units for absolute threshold for each channel is set in the 
channel probe menu.

•

When the 

Source

 is set to 

Math: f(t)

, the threshold 

Type

 can only be set 

to 

Percent

.

4

Press the 

Lower

 softkey; then, turn the Entry knob to set the lower 

measurement threshold value.

N O T E

Changing default thresholds may change measurement results

The default lower, middle, and upper threshold values are 10%, 50%, and 90% of the value 
between Top and Base. Changing these threshold definitions from the default values may 
change the returned measurement results for Average, Delay, Duty Cycle, Fall Time, 
Frequency, Overshoot, Period, Phase, Preshoot, Rise Time, +Width, and -Width.

T I P

Absolute threshold hints

• Absolute thresholds are dependent on channel scaling, probe attenuation, and probe units. 

Always set these values first before setting absolute thresholds.

• The minimum and maximum threshold values are limited to on-screen values.
• If any of the absolute threshold values are above or below the minimum or maximum waveform 

values, the measurement may not be valid.

Summary of Contents for 2000 X-Series

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands