manualshive.com logo in svg

Agilent Technologies 2000 X-Series, User Manual

Share
Download
Agilent Technologies 2000 X-Series User Manual Download Page 94

94

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

6

Digital Channels

 

To display digital channels as a bus

Digital channels may be grouped and displayed as a bus, with each bus 
value displayed at the bottom of the display in hex or binary. You can 
create  up  to  two  buses.  To  configure and display each bus, press the 

[Digital]

 key on the front panel. Then press the 

Bus

 softkey.

Next, select a bus. Rotate the Entry knob, then press the Entry knob or 
the 

Bus1/Bus2

  softkey  to  switch  it  on.

Use the 

Channel

 softkey and the Entry knob to select individual channels 

to  be  included  in  the  bus.  You  can  rotate  the  Entry  knob  and  push  it  or 
push the softkey to select channels. You can also press the 

Select/Deselect 

D7-D0

 softkey to include or exclude groups of eight channels in each bus.

If  the  bus  display  is  blank,  completely  white,  or  if  the  display  includes  "...", 
you need to expand the horizontal scale to allow space for the data to be 
shown, or use the cursors to display the values (see 

"Using cursors to read 

bus values"

on page 95).

The 

Base

 softkey lets you choose to display the bus values in hex or 

binary.

The buses are shown at the bottom of the display.

Summary of Contents for 2000 X-Series

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands