Agilent Technologies 2000 X-Series User Manual Download Page 84

Page: 84 / 352

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

Reference Waveforms

Display the desired reference waveform (see

"To display a reference

waveform"

on page 82).

Press the

Skew

softkey and turn the Entry knob to adjust the reference

waveform skew.

To display reference waveform information

Press the

[Ref]

key to turn on reference waveforms.

In the Reference Waveform Menu, press the

Options

softkey.

In the Reference Waveform Options Menu, press the

Display Info

softkey

to enable or disable reference waveform information on the oscilloscope
display.

Press the

Transparent

softkey to enable or disable transparent

information backgrounds.

This setting is also used for other oscilloscope information on the
display, like mask test statistics, etc.

To save/recall reference waveform files to/from a USB storage device

Analog channel, math, or reference waveforms can be saved to a reference
waveform file on a USB storage device. See

"To save reference waveform

files to a USB storage device"

on page 233.

You can recall a reference waveform file from a USB storage device into
one of the reference waveform locations. See

"To recall reference waveform

files from a USB storage device"

on page 236.

Summary of Contents for 2000 X-Series

































































































































































































































































































































































Search results

Summary of Contents for 2000 X-Series

Reviews:

Related manuals for 2000 X-Series

Brands by name

Popular brands

Agilent Technologies 2000 X-Series, User Manual

Search results

Summary of Contents for 2000 X-Series

Reviews:

Related manuals for 2000 X-Series

Brands by name

Popular brands