manualshive.com logo in svg

Agilent Technologies 2000 X-Series, User Manual

Share
Download
Agilent Technologies 2000 X-Series User Manual Download Page 337

UART/RS232 Triggering and Serial Decode

25

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

337

 

UART/RS232 Triggering

To set up the oscilloscope to capture UART/RS- 232 signals, see 

"Setup for 

UART/RS232 Signals"

on page 335.

To trigger on a UART (Universal Asynchronous Receiver/Transmitter) 
signal connect the oscilloscope to the Rx and Tx lines and set up a trigger 
condition. RS232 (Recommended Standard 232) is one example of a UART 
protocol.

1

Press 

[Trigger]

.

2

In the Trigger Menu, press the 

Trigger

 softkey; then, turn the Entry knob 

to select the serial slot (Serial 1) on which the UART/RS232 signals are 
being decoded.

3

Press the 

Trigger Setup

 softkey to open the UART/RS232 Trigger Setup 

Menu.

4

Press the 

Base

 softkey to select Hex or ASCII as the base displayed on 

the Data softkey in the UART/RS232 Trigger Setup Menu.

Note that the setting of this softkey does not affect the selected base of 
the decode display.

5

Press the 

Trigger

 softkey and set up the desired trigger condition:

•

Rx Start Bit

 — The oscilloscope triggers when a start bit occurs on Rx.

N O T E

In the serial decode display, the most significant bit is always displayed on the left 
regardless of how Bit Order is set.

Summary of Contents for 2000 X-Series

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands