manualshive.com logo in svg

Agilent Technologies 2000 X-Series, User Manual

Share
Download
Agilent Technologies 2000 X-Series User Manual Download Page 221

Waveform Generator

17

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

221

 

3

In the Waveform Generator Settings Menu, press the 

Modulation

 softkey.

4

In the Waveform Generator Modulation Menu:

•

Press the 

Modulation

 softkey to enable or disable modulated waveform 

generator output.

You can enable modulation for all waveform generator function types 
except pulse, DC, and noise.

•

Press the 

Type

 softkey and turn the Entry knob to select the 

modulation type:

•

Amplitude Modulation (AM)

 — the amplitude of the original carrier 

signal is modified according to the amplitude of the modulating 
signal. See 

"To set up Amplitude Modulation (AM)"

on page 221.

•

Frequency Modulation (FM)

 — the frequency of the original carrier 

signal is modified according to the amplitude of the modulating 
signal. See 

"To set up Frequency Modulation (FM)"

on page 223.

•

Frequency-Shift Keying Modulation (FSK)

 — the output frequency "shifts" 

between the original carrier frequency and a "hop frequency" at 
the specified FSK rate. The FSK rate specifies a digital square 
wave modulating signal. See 

"To set up Frequency- Shift Keying 

Modulation (FSK)"

on page 224.

To set up Amplitude Modulation (AM)

In the Waveform Generator Modulation Menu (under 

[Wave Gen] > Settings > 

Modulation

):

1

Press the 

Type

 softkey and turn the Entry knob to select 

Amplitude 

Modulation (AM)

.

2

Press the 

Waveform

 softkey and turn the Entry knob to select the shape 

of the modulating signal:

•

Sine

•

Square

•

Ramp

•

Sine Cardinal

Summary of Contents for 2000 X-Series

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands