manualshive.com logo in svg

Agilent Technologies 2000 X-Series, User Manual

Share
Download
Agilent Technologies 2000 X-Series User Manual Download Page 65

Vertical Controls

3

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

65

 

If Amps is chosen as the units and a manual attenuation factor is chosen, 
then the units as well as the attenuation factor are displayed above the 

Probe

 softkey.

To specify the probe skew

When measuring time intervals in the nanoseconds (ns) range, small 
differences in cable length can affect the measurement. Use 

Skew

 to 

remove cable- delay errors between any two channels.

1

Probe the same point with both probes.

2

Press one of the probes associated channel key.

3

In the Channel Menu, press 

Probe

.

4

In the Channel Probe Menu, press 

Skew

; then, select the desired skew 

value.

Each analog channel can be adjusted ±100 ns in 10 ps increments for a 
total of 200 ns difference.

The skew setting is not affected by pressing 

[Default Setup]

 or 

[Auto Scale]

.

Summary of Contents for 2000 X-Series

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands