manualshive.com logo in svg

Agilent Technologies 2000 X-Series, User Manual

Share
Download
Agilent Technologies 2000 X-Series User Manual Download Page 191

Measurements

14

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

191

 

Time Measurements

The following figure shows time measurement points.

The default lower, middle, and upper measurement thresholds are 10%, 
50%, and 90% between Top and Base values. See 

"Measurement 

Thresholds"

on page 196 for other percentage threshold and absolute value 

threshold settings.

•

"Period"

on page 191

•

"Frequency"

on page 192

•

"+ Width"

on page 193

•

"– Width"

on page 193

•

"Duty Cycle"

on page 193

•

"Rise Time"

on page 193

•

"Fall Time"

on page 193

•

"Delay"

on page 194

•

"Phase"

on page 195

Period

Period is the time period of the complete waveform cycle. The time is 
measured between the middle threshold points of two consecutive, 
like- polarity edges. A middle threshold crossing must also travel through 
the lower and upper threshold levels which eliminates runt pulses. The X 
cursors show what portion of the waveform is being measured. The Y 
cursor shows the middle threshold point.

Rise Time

+ Width

Fall Time

- Width

Period

Middle

Upper

Thresholds

Lower

Summary of Contents for 2000 X-Series

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands