Agilent Technologies 2000 X-Series User Manual Download Page 59

Page: 59 / 352

Agilent InfiniiVision 2000 X-Series Oscilloscopes
User's Guide

3
Vertical Controls

To turn waveforms on or off (channel or math)

To adjust the vertical scale

To adjust the vertical position

To specify channel coupling

To specify bandwidth limiting

To change the vertical scale knob's coarse/fine adjustment setting

To invert a waveform

Setting Analog Channel Probe Options

The vertical controls include:

•

The vertical scale and position knobs for each analog channel.

•

The channel keys for turning a channel on or off and accessing the
channel's softkey menu.

The following figure shows the Channel 1 Menu that appears after
pressing the

[1]

channel key.

Summary of Contents for 2000 X-Series

































































































































































































































































































































































Search results

Summary of Contents for 2000 X-Series

Reviews:

Related manuals for 2000 X-Series

Brands by name

Popular brands

Agilent Technologies 2000 X-Series, User Manual

Search results

Summary of Contents for 2000 X-Series

Reviews:

Related manuals for 2000 X-Series

Brands by name

Popular brands