manualshive.com logo in svg

Agilent Technologies 2000 X-Series, User Manual

The Agilent Technologies 2000 X-Series offers cutting-edge technology with a comprehensive user manual, allowing users to unlock its full potential. Download the free manual from manualshive.com to effortlessly navigate through its advanced features and maximize your experience with this exceptional product.

Share
Download
background image

282

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

22

Reference

 

•

"Transient Withstand Capability"

on page 283

Oscilloscope Measurement Category

The InfiniiVision oscilloscopes are intended to be used for measurements 
in Measurement Category I.

Measurement Category Definitions

Measurement category I is for measurements performed on circuits not 
directly connected to MAINS. Examples are measurements on circuits not 
derived from MAINS, and specially protected (internal) MAINS derived 
circuits. In the latter case, transient stresses are variable; for that reason, 
the transient withstand capability of the equipment is made known to the 
user.

Measurement category II is for measurements performed on circuits 
directly connected to the low voltage installation. Examples are 
measurements on household appliances, portable tools and similar 
equipment.

Measurement category III is for measurements performed in the building 
installation. Examples are measurements on distribution boards, 
circuit- breakers, wiring, including cables, bus- bars, junction boxes, 
switches, socket- outlets in the fixed installation, and equipment for 
industrial use and some other equipment, for example, stationary motors 
with permanent connection to the fixed installation.

Measurement category IV is for measurements performed at the source of 
the low- voltage installation. Examples are electricity meters and 
measurements on primary overcurrent protection devices and ripple 
control units.

WA R N I N G

Use this instrument only for measurements within its specified measurement 
category.

Summary of Contents for 2000 X-Series

































































































































































































































































































































































Reviews:

No comments

Related manuals for 2000 X-Series

ZOLL R Series In-Service Manual preview
R Series
Brand: ZOLL Pages: 5
Accu-Chek Compact Pocket User Manual preview
Compact
Brand: Accu-Chek Pages: 3
iBin Compact Installation Instructions preview
Compact
Brand: iBin Pages: 2
Tascam CD-RW5000 Owner'S Manual preview
CD-RW5000
Brand: Tascam Pages: 27
Jay-Lor A50 Owner'S Manual preview
A50
Brand: Jay-Lor Pages: 72
MacDon TM100 Manual preview
TM100
Brand: MacDon Pages: 198
M-Triangel M1 Operating Instruction preview
M1
Brand: M-Triangel Pages: 6
Bang & Olufsen BeoPlay A9 Quick Manual preview
BeoPlay A9
Brand: Bang & Olufsen Pages: 2
Garmin GNX Wind Owner'S Manual preview
GNX Wind
Brand: Garmin Pages: 10
Naviom AIS Installation Instructions Manual preview
AIS
Brand: Naviom Pages: 31
Ocean Sonics icListen User Manual preview
icListen
Brand: Ocean Sonics Pages: 45
Ultra Firefly Low Voltage Lighting System Installation Manual preview
Firefly Low Voltage Lighting System
Brand: Ultra Pages: 2
Lumination LUMEL Series Quick Start Manual preview
LUMEL Series
Brand: Lumination Pages: 2
Mindray Zonare ZS3 Instructions For Use Manual preview
Zonare ZS3
Brand: Mindray Pages: 165
B&G Mini DB Instruction Manual preview
Mini DB
Brand: B&G Pages: 2
Clas Ohlson TENS HV6609 Operating Instruction preview
TENS HV6609
Brand: Clas Ohlson Pages: 20
GLITCHMACHINES HYSTERESIS User Manual preview
HYSTERESIS
Brand: GLITCHMACHINES Pages: 8
ICE COBOTICS ICE USA i20NBL Operator'S & Parts Manual preview
ICE USA i20NBL
Brand: ICE COBOTICS Pages: 49

Brands by name

Popular brands

Load more brands