manualshive.com logo in svg

Agilent Technologies 2000 X-Series, User Manual

Share
Download
Agilent Technologies 2000 X-Series User Manual Download Page 344

344

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

25

UART/RS232 Triggering and Serial Decode

 

•

Rx Data

 — Finds a data byte that you specify. For use when the DUT 

data words are from 5 to 8 bits in length (no 9th (alert) bit).

•

Rx 1:Data

 — For use when the DUT data words are 9 bits in length 

including the alert bit (the 9th bit). Finds only when the 9th (alert) 
bit is 1. The specified data byte applies to the least significant 8 bits 
(excludes the 9th (alert) bit)

•

Rx 0:Data

 — For use when the DUT data words are 9 bits in length 

including the alert bit (the 9th bit). Finds only when the 9th (alert) 
bit is 0. The specified data byte applies to the least significant 8 bits 
(excludes the 9th (alert) bit).

•

Rx X:Data

 — For use when the DUT data words are 9 bits in length 

including the alert bit (the 9th bit). Finds a data byte that you 
specify regardless of the value of the 9th (alert) bit. The specified 
data byte applies to the least significant 8 bits (excludes the 9th 
(alert) bit).

•

Similar choices are available for Tx.

•

Rx or Tx Parity Error

 — Finds a parity error based on the parity you have 

set in the Bus Configuration Menu.

•

Rx or Tx Any Error

 — Finds any error.

For more information on searching data, see 

"Searching Lister Data"

on 

page 108.

For more information on using the 

[Navigate]

 key and controls, see 

"Navigating the Time Base"

on page 56.

Summary of Contents for 2000 X-Series

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands