ABB SafeMove2 Applications Manual Download Page 89 | Manualshive

Page: 89 / 238

ABB SafeMove2 Applications Manual Download Page 89

Explanation of

Base Frame

All values for the base frame are automatically loaded from the robot controller
and cannot be changed from the

Visual SafeMove

browser.

Description

Setting

Zone can be defined in either task frame, world coordinate
system, user coordinate system, or robot base frame. These
coordinate systems are often identical, but for MultiMove
systems it may be desired to do the configuration in the robot
base frame.

Base frame

•

Reference

X, Y and Z values for the selected reference frame’s origin,
expressed in the world coordinate system.

Base frame

•

Position X, Y, Z

Defines the orientation of the selected reference frame,
compared to the world coordinate system.

Base frame

•

Orientation

Additional axes parameters node

If the axis should be part of the SafeMove supervision, select the check box

Is

supervised

.

Joint

parameters

Description

Setting

Servo lag

is the estimated lag (in radians on motor side) for the

additional axis.

Servo lag

For more information, see

Servo Delay Factor and Servo Lag on

.

Estimated delay factor between reference position and measured
position (number of 4 ms units) when moving the additional axis.
(See TuneMaster, signal number 17 and 18.)

Servo delay factor

For more information, see

Servo Delay Factor and Servo Lag on

.

The maximum speed in manual mode.

Max speed manual
mode

Brake ramp supervision

parameters

Description

Setting

Selects if safe brake ramp should be used for the additional
axis.

Safe brake ramp enabled

(check box)

Delays the Safe Brake Ramp function. See figure below.

Ramp delay

Default value: 200 ms.

If the actual deceleration is lower than the specified

Brake

Ramp Limit

, then Safe Brake Ramp will cause a category 0

stop. The value is specified for the arm side.

Brake ramp limit

A speed offset for the Safe Brake Ramp function.

Start speed offset

Continues on next page

Application manual - Functional safety and SafeMove2

89

3HAC052610-001 Revision: P

© Copyright 2016-2020 ABB. All rights reserved.

4 The Visual SafeMove user interface in RobotStudio

4.5 The

Visual SafeMove

browser

Continued

«
...
87
88
89
90
91
...
»

Summary of Contents for SafeMove2















































































































































































































































Reviews:

No comments