manualshive.com logo in svg

ABB SafeMove2, Applications Manual, Page: 24 / 238

Share
Download
ABB SafeMove2 Applications Manual Download Page 24

Supervision of robot position and speed

The second type of supervision functionality (to supervise the robot position and
speed) is fulfilled by letting SafeMove compare the robot position and speed with
limit values configured by an authorized user (so called Safety User). If any value
is outside its defined safe area, the supervision functions will stop the robot (or
set an output signal).

To ensure that also this supervision complies with the category 3 requirement,
SafeMove is internally working with a two channel microprocessor based system.
Both processors make parallel calculations comparing the actual position and the
reference position.

24

Application manual - Functional safety and SafeMove2

3HAC052610-001 Revision: P

© Copyright 2016-2020 ABB. All rights reserved.

1 Introduction

1.2.4 Safe design of SafeMove

Continued

Summary of Contents for SafeMove2















































































































































































































































Reviews:

No comments