ABB SafeMove2 Applications Manual Download Page 38 | Manualshive

Page: 38 / 238

ABB SafeMove2 Applications Manual Download Page 38

2.2 General functions

2.2.1 Manual Operation Supervision

Manual Operation Supervision

Manual Operation Supervision is a function that is active in manual operating mode
and supervises that motion is below the configured manual mode supervision
speed.

Functionality

While Manual Operation Supervision is active, a supervision makes sure that the
tool center point (TCP), wrist center point (WCP), and elbow speed does not exceed
250 mm/s (unless a lower value is configured).

Manual Operation Supervision overrides safety functions by muting stops from
the safety controller due to supervision functions.

Note

If Manual Operation Supervision is active and the robot is jogged to a non-violation
position and then into a supervision violation position again, the robot will stop
again. The new violation must be confirmed by releasing the enabling device on
the FlexPendant before the jogging can be resumed.

DANGER

If Basic joint supervision mode is used, the supervision of the TCP, WCP, and
elbow speed is disabled.

Instead, axis speeds are supervised with limits set to approximate a Cartesian
speed limit, corresponding to the parameter

Max speed in manual mode

.

The user is responsible for validating that this speed limit satisfies the
requirements for safe manual mode operation.

If the speed in manual mode is determined to be too high, decrease the parameter

Max speed in manual mode

.

Settings

The following parameters can to be configured for Manual Operation Supervision:

•

Max speed in manual mode.

See

Configure Manual Operation Supervision on page 144

Function activation

Manual Operation Supervision is activated by switching to manual mode.

Dependencies to other supervision functions

Manual Operation Supervision can be used in combination with all other SafeMove
functions.

38

Application manual - Functional safety and SafeMove2

3HAC052610-001 Revision: P

© Copyright 2016-2020 ABB. All rights reserved.

2 SafeMove functions

2.2.1 Manual Operation Supervision

«
...
36
37
38
39
40
...
»

Summary of Contents for SafeMove2















































































































































































































































Reviews:

No comments