Tennant 6200E Скачать руководство пользователя страница 143

Страница: 143 / 222

ELECTRICAL

4-23

6200E 330415 (5--99)

4. Remove the four screws and nuts holding

the controller to the electrical panel. Remove

the controller from the machine.

5. Install the new controller onto the electrical

panel in the same orientation as the old one.

Reinstall the hardware and hand tighten.

NOTE: Do not over tighten.

6. Reconnect the wires to the new controller.

See schematic in this section.

7. Pivot the instrument panel back onto the

front shroud. Reinstall the hardware and

hand tighten tight. See TO ACCESS

CIRCUIT BREAKER OR INSTRUMENT

PANEL instructions.

8. Start the machine and check the new

controller for proper operation.

Содержание 6200E































































































































































































































Результаты поиска

Содержание 6200E

Отзывы:

Похожие инструкции для 6200E

Бренды по названию

Популярные бренды

Tennant 6200E, Руководство по обслуживанию

Результаты поиска

Содержание 6200E

Отзывы:

Похожие инструкции для 6200E

Бренды по названию

Популярные бренды