Tennant 6200E Скачать руководство пользователя страница 80

Страница: 80 / 222

SWEEPING

3-8

6200E 330415 (12--01)

9. Place the edges of the shaker firmly

between the filter and the filter seal.

NOTE: When installed properly, the shaker plate

cannot move in either front--to--back or

side--to--side directions. If the shaker is loose, it

will not function properly.

10. The filter shaker should lay flat against the

filter. Check to make sure the comb tab is

not caught below the filter shaker plate.

11. Check the shaker solenoid gap with the end

of the shipping tab. The gap should be the

same width as the tab. If it is not, loosen the

mounting screws, adjust the gap by

repositioning the shaker solenoid, then

retighten the screws.

12. Return the filter back to the machine.

Содержание 6200E































































































































































































































Результаты поиска

Содержание 6200E

Отзывы:

Похожие инструкции для 6200E

Бренды по названию

Популярные бренды

Tennant 6200E, Руководство по обслуживанию

Результаты поиска

Содержание 6200E

Отзывы:

Похожие инструкции для 6200E

Бренды по названию

Популярные бренды