Tennant 6200E Скачать руководство пользователя страница 82

Страница: 82 / 222

SWEEPING

3-10

6200E 330415 (6--99)

MAIN BRUSH

The main brush is cylindrical and spans the width

of the machine, sweeping debris into the hopper.

Check the brush daily for wear or damage.

Remove any string or wire tangled on the main

brush, main brush drive hub, or main brush idler

hub.

Check the main brush pattern weekly. The pattern

should be 50 to 75 mm (2 to 3 in) wide with the

main brush in the lowered position.

Rotate the main brush end-for-end after every 50

hours of operation for maximum brush life and

best sweeping performance.

Replace the main brush when the remaining

bristles measure 25 mm (1 in) in length.

TO REPLACE MAIN BRUSH

FOR SAFETY: Before Leaving Or

Servicing Machine; Stop On Level

Surface, Set Parking Brake.

1. Stop the machine, set the parking brake and

turn the machine power off.

2. Open the left side main brush access door.

3. Loosen the idler arm mounting knob and

three other side skirt mounting knobs.

Remove the brush idler arm assembly.

Содержание 6200E































































































































































































































Результаты поиска

Содержание 6200E

Отзывы:

Похожие инструкции для 6200E

Бренды по названию

Популярные бренды

Tennant 6200E, Руководство по обслуживанию

Результаты поиска

Содержание 6200E

Отзывы:

Похожие инструкции для 6200E

Бренды по названию

Популярные бренды