Tennant 6200E Скачать руководство пользователя страница 2

Страница: 2 / 222

This service manual is intended to be used as an aid in the detailed service, repair, and troubleshooting of
your TENNANT Model 6200E.

The set is organized into five major groups: General Information, Chassis, Sweeping, Electrical, and

Hydraulics.

General Information

: Safety precautions, machine specifications, machine maintenance chart, machine

tieing, machine jacking, machine storing, machine pushing or towing, and hardware information.

Chassis:

Tire/wheel replacement, brake adjustment and replacement, steering adjustment and

replacement.

Sweeping:

V--belt replacement, brush replacement, bearing replacement, skirt/seal repair/replacement,

and sweeping troubleshooting.

Electrical:

Battery maintenance and replacement, electrical schematics, and electrical troubleshooting.

Hydraulics:

Cylinder replacement/repair, pump replacement/repair, hydraulic schematic, and hydraulic

troubleshooting.

Manual Number -- 330415

Revision: 01

Published: 12--01

1999, 2001 TENNANT, Printed in U.S.A.

Содержание 6200E































































































































































































































Результаты поиска

Содержание 6200E

Отзывы:

Tennant 6200E, Руководство по обслуживанию, Страница: 2 / 222

Результаты поиска

Содержание 6200E

Отзывы: