Tennant 6200E Скачать руководство пользователя страница 198

Страница: 198 / 222

ELECTRICAL

4-78

6200E 330415 (6--99)

VACUUM FAN MOTOR

The vacuum fan motor will only operate when the

hopper is down, fan/shake filter rocker switch is in

the fan position, and the vehicle is in motion.

Electrical components needed to operate the

vacuum fan motor circuit:

CB--1, Key switch, Stop switch, M1 main

contactor, M1a aux. contact, 1242 motor

controller, Fan/shake filter switch, CB--8, M3

brush contactor, Main brush motor.

1. Control circuit. (see fig. 10)

For the vacuum fan motor to operate, the

machine must be started with the M1 contactor

energized. The hopper should be lowered

completely allowing the hopper down switch to

close. Engaging the Fan/shake filter rocker switch

in the fan position pr36 volts to the (+)

terminal of the vacuum fan contactor coil. Finally,

when the machine is commanded to move from

the propel foot control, the controller completes

the circuit with --36 volts from pin 8 of the motor

controller to the (--) coil terminal of the vacuum fan

contactor M3.

2. Power circuit. (see fig. 11)

When the M3 contactor is energized, current

flows through CB--7, the M3 contacts, and finally

the vacuum fan motor.

Содержание 6200E































































































































































































































Результаты поиска

Содержание 6200E

Отзывы:

Похожие инструкции для 6200E

Бренды по названию

Популярные бренды

Tennant 6200E, Руководство по обслуживанию

Результаты поиска

Содержание 6200E

Отзывы:

Похожие инструкции для 6200E

Бренды по названию

Популярные бренды