Tennant 6200E Скачать руководство пользователя страница 14

Страница: 14 / 222

GENERAL INFORMATION

1-12

6200E 330415 (12--01)

MACHINE JACKING

Empty the hopper before jacking the machine.

You can jack up the machine for service at the

designated locations. Use a hoist or jack that will

support the weight the machine. Always stop the

machine on a flat, level surface and block the tires

before jacking up the machine.

FOR SAFETY: Before leaving or

servicing machine, stop on level

surface, set parking brake, turn off

machine, and remove key.

The front jacking locations are on the flat bottom

edge of the front of the machine frame.

The rear jacking locations are on the corners of

the rear frame.

FOR SAFETY: When servicing machine,

block machine tires before jacking up

machine.

FOR SAFETY: When servicing machine,

jack up machine at designated locations

only. Block machine up with jack

stands.

STORING MACHINE

Before storing the machine for an extended time,

the machine needs to be serviced to lessen the

chance of rust, sludge, and other undesirable

deposits from forming.

Содержание 6200E































































































































































































































Результаты поиска

Содержание 6200E

Отзывы:

Похожие инструкции для 6200E

Бренды по названию

Популярные бренды

Tennant 6200E, Руководство по обслуживанию

Результаты поиска

Содержание 6200E

Отзывы:

Похожие инструкции для 6200E

Бренды по названию

Популярные бренды