Tennant 6200E Скачать руководство пользователя страница 45

Страница: 45 / 222

CHASSIS

2-27

6200E 330415 (6--99)

4. Remove the four hex screws holding the

pivot and sprocket assembly to the drive

assembly.

5. Remove the sprocket from the pivot

assembly.

6. Remove the cotter pin and castle nut from

the upper swivel plate weldment.

7. Remove the flat washer and old cone

bearing from the bottom swivel plate.

8. Install the new cone bearing and flat washer

on the bottom swivel plate. Make sure the

new cone bearing is greased.

9. Reinstall the castle nut and tighten to

200 Nm (150 ft lbs). Then tighten to the next

nearest hole and install the cotter pin.

10. Reinstall the sprocket on the pivot assembly.

Содержание 6200E































































































































































































































Результаты поиска

Содержание 6200E

Отзывы:

Похожие инструкции для 6200E

Бренды по названию

Популярные бренды

Tennant 6200E, Руководство по обслуживанию

Результаты поиска

Содержание 6200E

Отзывы:

Похожие инструкции для 6200E

Бренды по названию

Популярные бренды