Tennant 6200E Скачать руководство пользователя страница 51

Страница: 51 / 222

CHASSIS

2-33

6200E 330415 (6--99)

TO REPLACE FRONT TIRE AND WHEEL

ASSEMBLY

FOR SAFETY: Before Leaving Or

Servicing Machine; Stop On Level

Surface, Set Parking Brake.

1. Raise the seat support and unplug the

battery connectors.

2. Raise the front of the machine and place

jack stands under the frame.

3. Mark and remove the electrical cables

leading to the drive motor.

4. Remove the four hex screws holding the

outer plate, motor, and planetary gear box to

the main drive assembly.

5. Pull the planetary gear box, outer plate, and

motor out of the drive wheel and away from

the drive assembly.

6. Go to the other side of the drive assembly

and remove the hub cap. This will expose

the outer bearing, hex sleeve, and lock bolt.

Содержание 6200E































































































































































































































Результаты поиска

Содержание 6200E

Отзывы:

Похожие инструкции для 6200E

Бренды по названию

Популярные бренды

Tennant 6200E, Руководство по обслуживанию

Результаты поиска

Содержание 6200E

Отзывы:

Похожие инструкции для 6200E

Бренды по названию

Популярные бренды