manualshive.com logo in svg

Tennant 6200E, Руководство по обслуживанию, Страница: 154 / 222

Поделиться
Скачать
Tennant 6200E Скачать руководство пользователя страница 154

ELECTRICAL

4-34

6200E 330415 (5--99)

12. Remove the four flat head screws holding

the main brush motor to the motor pivot

plate and machine frame.

NOTE: You may have to rotate the brush arm

weldment to line up the access holes.

13. Go under the front of the machine and

locate the main brush motor behind the front

drive assembly. Disconnect the main brush

motor from the main harness.

14. Remove the main brush motor from the

machine.

NOTE: Note the orientation of the motor and

electrical wires.

15. Install the new main brush motor into the

machine.

NOTE: Make sure to orientate the motor so the

wires are pointed to the front of the machine.

16. Connect the new main brush motor to the

main harness.

17. Wire tie the motor wires to the motor

housing.

18. Line up the mount holes in the new motor

with the mount holes in the machine frame

and motor pivot plate. Reinstall the four flat

head screws. Tighten to 11 -- 14 Nm

(7 -- 10 ft lb).

NOTE: You may have to rotate the brush arm

weldment to line up the access holes.

Содержание 6200E































































































































































































































Отзывы:

Нет отзывов