Tennant 6200E Скачать руководство пользователя страница 70

Страница: 70 / 222

CHASSIS

2-52

6200E 330415 (6--99)

16. Reinstall the steering housing in the

machine. Reinstall the two hex screws.

Leave loose for now.

17. Position the long steering shaft and steering

wheel into the top of the steering U--joint.

Tighten the set screws tight.

18. Go under the machine and reinstall the

steering chain around the small steering

sprocket. Reinstall the master link.

19. Turn the steering wheel all the way to the left

and then to the right. Find the point in the

rotation where the steering chain is the most

tight.

20. Push the bearing housing forward in the

slots. This will remove any excess slack in

the steering chain. Tighten the two hex

screws to 37 -- 48 Nm (26 -- 34 ft lb).

21. Remove the jack stands and lower the

machine to the floor. Operate the machine

and check the steering chain for proper

operation.

Содержание 6200E































































































































































































































Результаты поиска

Содержание 6200E

Отзывы:

Tennant 6200E, Руководство по обслуживанию, Страница: 70 / 222

Результаты поиска

Содержание 6200E

Отзывы: