manualshive.com logo in svg

Tennant 6200E, Руководство по обслуживанию, Страница: 118 / 222

Поделиться
Скачать
Tennant 6200E Скачать руководство пользователя страница 118

SWEEPING

3-46

6200E 330415 (6--99)

4. Use a arbor press to remove the fan shaft

and two bearings from the housing.

5. Use the arbor press to install the new

bearings into the housing.

NOTE: The short end of fan shaft is on the side of

housing with the thin flange. The long end of fan

shaft is on the side of the housing with the wide

flange.

NOTE: Make sure the bearings are pressed down

tight. The fan will be noisy if there is any play in

the bearings. The retaining rings must be tight to

the housing.

6. Reinstall the bearing housing onto the

bearing housing plate. The long end of the

shaft is on the side with the sound foam.

Reinstall the four hex screws and washers.

Tighten to 8 -- 10 Nm (6 -- 8 ft lb).

7. Reinstall the V--belt pulley on the short end

of the fan shaft.

The recessed side of the

pulley goes to the inside

. Hand tighten the

set screws tight.

Содержание 6200E































































































































































































































Отзывы:

Нет отзывов