manualshive.com logo in svg

Tennant 6200E, Руководство по обслуживанию, Страница: 49 / 222

Поделиться
Скачать
Tennant 6200E Скачать руководство пользователя страница 49

CHASSIS

2-31

6200E 330415 (6--99)

TO INSTALL PLANETARY GEAR BOX

FOR SAFETY: Before Leaving Or

Servicing Machine; Stop On Level

Surface, Set Parking Brake.

1. Install the new planetary gearbox on the

outer motor mount plate. Install the 6 socket

screws into the planetary gear box. Torque

the 6 screws to 193 Ncm -- 250 Ncm.

NOTE: Do not tighten this hardware above a

grade 2 torque. The planetary gearbox is made

from a softer grade of cast iron and the threads

could strip out.

2. Reinstall the outer motor mount plate and

gear box on the drive assembly. Tighten the

four screws to 18 -- 24 Nm (15 -- 20 ft lb).

NOTE: When installing the motor on the drive

assembly, make sure the terminals are pointing up

and slightly forward for proper electrical cable

installation.

3. Reinstall the electric motor on the drive

assembly. Make sure to line up the splines

on the motor shaft with the splines of the

planetary gear box. Tighten the 4 hex

screws to 18 -- 24 Nm (15 -- 20 ft lb).

Содержание 6200E































































































































































































































Отзывы:

Нет отзывов