Tennant 6200E Скачать руководство пользователя страница 12

Страница: 12 / 222

GENERAL INFORMATION

1-10

6200E 330415 (12--01)

PUSHING, TOWING, AND TRANSPORTING

THE MACHINE

PUSHING OR TOWING THE MACHINE

If the machine becomes disabled, it can be

pushed or towed from the front or rear, but it is

easier and more stable to tow from the front end.

Only push or tow the machine for a

very short

distance

and do not exceed 3.2 kp/h (2 mph). It is

NOT intended to be pushed or towed for a long

distance or at a high speed.

ATTENTION! Do not push or tow

machine for a long distance or damage

may occur to the propelling system.

TRANSPORTING THE MACHINE

1. Position the front of the machine at the

loading edge of the truck or trailer.

FOR SAFETY: Use truck or trailer that

will support the weight of the machine.

NOTE: Empty the hopper before transporting the

machine.

2. If the loading surface is not horizontal or is

higher than 380 mm (15 in) from the ground,

use a winch to load machine.

If the loading surface is horizontal AND is

380 mm (15 in) or less from the ground, the

machine may be driven onto the truck or

trailer.

3. To winch the machine onto the truck or

trailer, attach the winching chains to the

front tie down located in the front of the

machine frame.

FOR SAFETY: When loading machine

onto truck or trailer, use winch. Do not

drive the machine onto the truck or

trailer unless the loading surface is

horizontal AND is 380 mm (15 in) or less

from the ground.

Содержание 6200E































































































































































































































Результаты поиска

Содержание 6200E

Отзывы:

Похожие инструкции для 6200E

Бренды по названию

Популярные бренды

Tennant 6200E, Руководство по обслуживанию

Результаты поиска

Содержание 6200E

Отзывы:

Похожие инструкции для 6200E

Бренды по названию

Популярные бренды