Tennant 6200E Скачать руководство пользователя страница 61

Страница: 61 / 222

CHASSIS

2-43

6200E 330415 (6--99)

STEERING

The steering on the model 6200E is controlled

with two sprockets and one chain. A large

diameter sprocket is mounted on the top of the

front drive assembly and a small diameter

sprocket is mounted on the bottom of the steering

shaft. The steering chain runs around both of

these sprockets.

After extended use, the steering chain may

stretch slightly. Any slack in the chain can be

removed by following the adjustment procedure

listed below.

TO ADJUST STEERING CHAIN

FOR SAFETY: Before Leaving Or

Servicing Machine; Stop On Level

Surface, Set Parking Brake.

1. Go into the operators compartment and

locate the two hex screws holding the lower

steering shaft bearing assembly to the floor

plate. Loosen these two hex screws.

2. Push the lower steering shaft assembly

forward until the slack has been removed

from the steering chain. Tighten the two hex

screws to 18 -- 24 Nm (15 -- 20 ft lb).

3. Operate the machine and check the steering

for proper operation.

NOTE: There is also a half link that can be

removed for more adjustment.

Содержание 6200E































































































































































































































Результаты поиска

Содержание 6200E

Отзывы:

Tennant 6200E, Руководство по обслуживанию, Страница: 61 / 222

Результаты поиска

Содержание 6200E

Отзывы: