Tennant 6200E Скачать руководство пользователя страница 62

Страница: 62 / 222

CHASSIS

2-44

6200E 330415 (6--99)

TO REPLACE STEERING CHAIN

FOR SAFETY: Before Leaving Or

Servicing Machine; Stop On Level

Surface, Set Parking Brake.

1. Raise the seat support and unplug the

battery connectors.

2. Raise the front of the machine and place

jack stands under the frame.

3. Go under the machine and locate the

steering chain.

4. Rotate the steering wheel until the master

link on the chain is accessible.

5. Remove the chain master link. Remove the

steering chain from both sprockets.

6. Remove and discard the steering chain from

the machine.

7. Route the new chain around both steering

sprockets. Install the master link.

8. Remove the jack stands and lower the

machine.

9. Operate the machine and check the steering

for proper operation.

Содержание 6200E































































































































































































































Результаты поиска

Содержание 6200E

Отзывы:

Похожие инструкции для 6200E

Бренды по названию

Популярные бренды

Tennant 6200E, Руководство по обслуживанию

Результаты поиска

Содержание 6200E

Отзывы:

Похожие инструкции для 6200E

Бренды по названию

Популярные бренды