manualshive.com logo in svg

Tennant 6200E, Руководство по обслуживанию, Страница: 98 / 222

Поделиться
Скачать
Tennant 6200E Скачать руководство пользователя страница 98

SWEEPING

3-26

6200E 330415 (12--01)

SIDE BRUSH

The side brush sweeps debris along edges into

the path of the main brush.

Check the brush daily for wear or damage.

Remove any string or wire found tangled on the

side brush or side brush drive hub.

Check the side brush pattern daily. The side brush

bristles should contact the floor in a 10 o’clock to

3 o’clock pattern when the brush is in motion.

Adjust the side brush pattern by loosening the hex

screw located above the side brush cable pulley in

the front of the operators compartment. Move the

pulley mount bracket up or down to achieve the

proper side brush pattern. Retighten the hex

screw.

The side brush should be replaced when it no

longer sweeps effectively for your application. A

guideline length is when the remaining bristles

measure 50 mm (2 in) in length. You may need to

replace the side brush sooner if you are sweeping

light litter or use a brush with shorter bristles if you

are sweeping heavy debris.

TO REPLACE SIDE BRUSH

1. Stop the machine, set the parking brake and

turn the machine power off.

FOR SAFETY: Before Leaving Or

Servicing Machine; Stop On Level

Surface, Set Parking Brake.

2. Remove the side brush retaining pin from

the side brush drive shaft by pulling the pin

keeper off over the end of the pin.

Содержание 6200E































































































































































































































Отзывы:

Нет отзывов