Tennant 6200E Скачать руководство пользователя страница 127

Страница: 127 / 222

ELECTRICAL

4-7

6200E 330415 (12--01)

8. The Tennant charger will start automatically.

When the batteries are fully charged, the

Tennant charger will automatically turn off.

NOTE: Use a charger with the proper rating for

the batteries to prevent damage to the batteries or

reduce the battery life.

NOTE: If the charger needs to be disconnected

from the machine before the batteries are fully

charged and the charger has not automatically

shut off, turn off the charger before disconnecting.

9. After the charger has turned off, unplug the

charger connector from the battery

connector on the machine.

10. Reconnect the battery connector to the

machine connector.

11. Check the electrolyte level in each battery

cell. Add just enough distilled water to bring

the electrolyte level up to the bottom of the

fill rings.

FOR SAFETY: When maintaining or

servicing machine, avoid contact with

battery acid.

12. Close the seat support.

Содержание 6200E































































































































































































































Результаты поиска

Содержание 6200E

Отзывы:

Tennant 6200E, Руководство по обслуживанию, Страница: 127 / 222

Результаты поиска

Содержание 6200E

Отзывы: