Tennant 6200E Скачать руководство пользователя страница 27

Страница: 27 / 222

CHASSIS

2-9

6200E 330415 (6--99)

6. Go to the other side of the drive assembly

and remove the hub cap. This will expose

the outer bearing, hex sleeve, and lock bolt.

7. Remove the lock bolt.

(this is a right--hand thread screw).

8. Remove the hex sleeve and outer bearing

cone assembly.

(this is a left hand thread nut).

9. The axle/tire/wheel assembly can now be

removed from the drive assembly. This will

expose the brake shoes.

10. Loosen the two jam nuts on the brake cable,

where it attaches to the drive support

casting. Pull the brake cable off the drive

assembly.

11. Remove the large ”C” spring holding the two

brake shoes together. Remove the brake

shoes.

NOTE: There is a great deal of tension on the ”C”

spring. Care must be used when spreading the

spring for removal or installation.

12. Install the new brake shoes on the drive

assembly in the same orientation as the old

ones were removed.

13. Reinstall the ”C” spring on the new brake

shoes.

Содержание 6200E































































































































































































































Результаты поиска

Содержание 6200E

Отзывы:

Похожие инструкции для 6200E

Бренды по названию

Популярные бренды

Tennant 6200E, Руководство по обслуживанию

Результаты поиска

Содержание 6200E

Отзывы:

Похожие инструкции для 6200E

Бренды по названию

Популярные бренды