Tennant 6200E Скачать руководство пользователя страница 25

Страница: 25 / 222

CHASSIS

2-7

6200E 330415 (6--99)

TO ADJUST PARKING BRAKE

The parking brake should be adjusted when an

excessive amount of brake pedal stroke is needed

to hold the machine.

FOR SAFETY: Before Leaving Or

Servicing Machine; Stop On Level

Surface, Block Rear Wheels.

1. Go under the machine in the front right

corner.

2. Locate the area where the brake cable

attaches to the drive support. The beginning

adjustment should be

1.375 in.

of conduit

showing on the cable end.

3. Turn the steering wheel all the way to the

right.

NOTE: Spin the tire/wheel assembly to make sure

the brakes are not dragging with the brake pedal

NOT engaged.

4. Loosen the two jam nuts on the brake cable,

where it attaches to the drive support

casting.

5. Move the cable away from the brake lever

far enough to remove the slack in the pedal

movement.

6. Re--tighten the two jam nuts firmly. Operate

the machine and check the brake pedal for a

shorter stroke.

Содержание 6200E































































































































































































































Результаты поиска

Содержание 6200E

Отзывы:

Tennant 6200E, Руководство по обслуживанию, Страница: 25 / 222

Результаты поиска

Содержание 6200E

Отзывы: