manualshive.com logo in svg

Tennant 6200E, Руководство по обслуживанию, Страница: 30 / 222

Поделиться
Скачать
Tennant 6200E Скачать руководство пользователя страница 30

CHASSIS

2-12

6200E 330415 (6--99)

REAR TIRES AND WHEELS

The rear tires on the model 6200E are

semi--pneumatic. The rear tire and wheel

assemblies are idler wheels only, they have no

braking capabilities.

TO REMOVE REAR TIRE

FOR SAFETY: Before Leaving Or

Servicing Machine; Stop On Level

Surface, Set Parking Brake.

1. Jack up the rear corner of the machine

where the tire needs to be removed.

NOTE: Do not raise both rear wheels off the floor

at the same time. The machine will become

unstable because of the single front tire.

2. Go under the machine in the area of the rear

tire. Locate the lock nut holding the axle

shaft to the machine frame. Remove the

lock nut and washer.

3. Support the tire while you pull the axle out of

the wheel assembly. Drop the wheel

assembly out of the machine.

Содержание 6200E































































































































































































































Отзывы:

Нет отзывов