Tennant 6200E Скачать руководство пользователя страница 125

Страница: 125 / 222

ELECTRICAL

4-5

6200E 330415 (12--01)

NOTE: Do not take readings immediately after

adding distilled water. If the water and acid are not

thoroughly mixed, the readings may not be

accurate. Check the hydrometer readings against

the following chart to determine the remaining

battery charge level:

Spec. Gravity at 27

C (80

Charge Level

235 AH Battery

100 %

1.265

75 %

1.223

50 %

1.185

25 %

1.148

Discharged

1.110

NOTE: If the readings are taken when the battery

electrolyte is any temperature other than shown,

the reading must be temperature corrected. Add

or subtract to the specific gravity reading 0.004,

4 points, for each 6

C (10

F) above or below

C (77

F).

TO CHARGE BATTERIES

1. Drive the machine to a flat, dry surface in a

well-ventilated area.

2. Stop the machine, set the parking brake and

turn the machine power off.

FOR SAFETY: Before leaving or

servicing machine, stop on level

surface, set parking brake, turn off

machine, and remove key.

3. Open the seat support.

4. Check the water level in all the battery cells.

08247

Содержание 6200E































































































































































































































Результаты поиска

Содержание 6200E

Отзывы:

Похожие инструкции для 6200E

Бренды по названию

Популярные бренды

Tennant 6200E, Руководство по обслуживанию

Результаты поиска

Содержание 6200E

Отзывы:

Похожие инструкции для 6200E

Бренды по названию

Популярные бренды