Tennant 6200E Скачать руководство пользователя страница 111

Страница: 111 / 222

SWEEPING

3-39

6200E 330415 (12--01)

TO ADJUST VACUUM FAN DRIVE BELT

TENSION

FOR SAFETY: Before Leaving Or

Servicing Machine; Stop On Level

Surface, Set Parking Brake.

1. To access the vacuum fan drive belt, remove

the right hand side panel. Start by lifting up

on the panel, pop the brush lift slot over the

black knob, then move the panel backward

and off the machine.

2. Loosen the four hex screws holding the

vacuum fan housing to the machine frame.

3. Pull the vacuum fan assembly toward the

back of the machine to tighten the V--belt.

The correct tension is when the belt deflects

13.0 mm (0.50 in) from a force of 17 kg

(38 lb) at belt midpoint.

4. Tighten the four vacuum housing mount

screws hand tight.

5. Reinstall the right hand machine cover.

6. Operate the machine. Check the vacuum

fan for proper operation.

Содержание 6200E































































































































































































































Результаты поиска

Содержание 6200E

Отзывы:

Похожие инструкции для 6200E

Бренды по названию

Популярные бренды

Tennant 6200E, Руководство по обслуживанию

Результаты поиска

Содержание 6200E

Отзывы:

Похожие инструкции для 6200E

Бренды по названию

Популярные бренды