Tennant 6200E Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 222

background image

GENERAL INFORMATION

1-13

6200E 330415 (6--99)

HARDWARE INFORMATION

The following charts state standard plated

hardware tightening ranges for normal assembly
applications. Decrease the specified torque by
20% when using a thread lubricant. Do not
substitute lower grade hardware for higher grade
hardware. If higher grade hardware than specified
is substituted, tighten only to the specified
hardware torque value to avoid damaging the

threads of the part being threaded into, as when
threading into speed nuts or weldments.

STANDARD BOLT TORQUE CHART

Thread

Size

SAE Grade 5

Torque ft lb

(Nm)

SAE Grade 8

Torque ft lb

(Nm)

0.25 in

7--10 (9--14)

10--13 (14--38)

0.31 in

15--20 (20--27)

20--26 (27--35)

0.38 in

27--35 (37--47)

36--47 (49--64)

0.44 in

43--56 (58--76)

53--76 (72--103)

0.50 in

65--85 (88--115)

89--116

(121--157)

0.62 in

130--170

(176--231)

117--265

(159--359)

0.75 in

215--280

(291--380)

313--407

(424--552)

1.00 in

500--650

(678--881)

757--984

(1026--1334)

NOTE: Decrease torque by 20% when using a
thread lubricant.

METRIC BOLT TORQUE CHART

Thread

Size

Class 8.8

Torque ft lb

_Nm)

Class 10.9

Torque ft lb

(Nm)

M4

2 (3)

3 (4)

M5

4 (5)

6 (8)

M6

7 (9)

10 (14)

M8

18 (24)

25 (34)

M10

32 (43)

47 (64)

M12

58 (79)

83 (112)

M14

94 (127)

133 (180)

M16

144 (195)

196 (265)

M20

260 (352)

336 (455)

M24

470 (637)

664 (900)

NOTE: Decrease torque by 20% when using a

thread lubricant.

Exceptions to the above chart:

Check the machine for exceptions!

BOLT IDENTIFICATION

Identification

Grade Marking

Specification and

Grade

SAE--Grade 5

SAE--Grade 8

ISO--Grade 8.8

ISO--Grade 10.9

01395

THREAD SEALANT AND LOCKING
COMPOUNDS

Thread sealants and locking compounds may be
used on this machine. They include the following:

Locktite 515 sealant -- gasket forming
material. TENNANT Part No. 75567,15 oz
(440 ml) cartridge.

Locktite 242 blue -- medium strength thread
locking compound. TENNANT Part No.

32676, 0.5 ml tube.

Locktite 271 red -- high strength thread
locking compound. TENNANT Part No.
19857, 0.5 ml tube.

«
...
13
14
15
16
17
...
»

Содержание 6200E































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 6200E

Бренд: American-Lincoln Страницы: 160

Бренд: Expert Страницы: 12

Бренд: floorex Страницы: 19

Бренд: Kärcher Страницы: 20

BD 70/75 W Classic Bp Pack 80 Ah Li

Бренд: Kärcher Страницы: 48

Бренд: Taski Страницы: 2

Бренд: BART Страницы: 24

Бренд: ICE COBOTICS Страницы: 2

Бренд: ICE COBOTICS Страницы: 27

Бренд: ICE COBOTICS Страницы: 47

i-SYNEGY i20NBTL+

Бренд: ICE COBOTICS Страницы: 41

Бренд: Lavorwash Страницы: 88

Бренд: Tornado Страницы: 20

Бренд: Tornado Страницы: 25

soldering S-LS-54

Бренд: STAMOS Страницы: 17

Бренд: XPower Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды