Tennant 6200E Скачать руководство пользователя страница 37

Страница: 37 / 222

CHASSIS

2-19

6200E 330415 (6--99)

TO INSTALL FRONT DRIVE ASSEMBLY

FOR SAFETY: Before Leaving Or

Servicing Machine; Stop On Level

Surface, Set Parking Brake.

1. Raise the seat support and unplug the

battery connectors.

2. Raise the front of the machine and place

jack stands under the frame.

3. Place the front drive assembly on a floor

jack or transmission jack. This will support

the drive assembly when installing it in the

machine.

4. Position the drive assembly under the

machine in front.

5. Raise the drive assembly up until the mount

holes in the floor plate are aligned with the

mount holes in the upper swivel plate

weldment on top of the drive assembly.

NOTE: Make sure to position the grease zerk in

the access hole in the machine floor plate.

6. Install the four button head screws and

tighten to 64 -- 83 Nm (47 -- 61 ft lb).

7. Reinstall the steering chain and master link.

Adjust the steering chain. See TO ADJUST

STEERING CHAIN instructions.

8. Reinstall the brake cable on the wheel

support. Tighten the jam nut on the brake

cable where it attaches to the wheel support.

Содержание 6200E































































































































































































































Результаты поиска

Содержание 6200E

Отзывы:

Похожие инструкции для 6200E

Бренды по названию

Популярные бренды

Tennant 6200E, Руководство по обслуживанию

Результаты поиска

Содержание 6200E

Отзывы:

Похожие инструкции для 6200E

Бренды по названию

Популярные бренды