Tennant 6200E Скачать руководство пользователя страница 126

Страница: 126 / 222

ELECTRICAL

4-6

6200E 330415 (12--01)

5. If the level is low, add just enough distilled

water to cover the plates. DO NOT

OVERFILL. The batteries can overflow

during charging due to expansion.

NOTE: Make sure the battery caps are in place

while charging.

FOR SAFETY: When maintaining or

servicing machine, avoid contact with

battery acid.

6. Unplug the battery connector from the

machine connector.

7. Plug the connector from the batteries into

the battery charger connector.

WARNING: Batteries emit hydrogen gas.

Explosion or fire can result. Keep

sparks and open flame away. Keep

covers open when charging.

NOTE: Plug the charger connector into connector

that runs to the batteries. Do not plug charger into

mounted connector. Damage may occur to the

machine.

NOTE: If the red “ABNORMAL CYCLE” lamp

lights when the batteries are plugged into the

TENNANT charger, this indicates that something

is wrong with the battery. The charger can not

charge the battery when this happens.

Содержание 6200E































































































































































































































Результаты поиска

Содержание 6200E

Отзывы:

Tennant 6200E, Руководство по обслуживанию, Страница: 126 / 222

Результаты поиска

Содержание 6200E

Отзывы: