Tennant 6200E Скачать руководство пользователя страница 38

Страница: 38 / 222

CHASSIS

2-20

6200E 330415 (6--99)

9. Reinstall the cotter pin and clevis pin in the

end of the brake cable where it attaches to

the lever on the wheel support.

10. Turn the steering wheel all the way to the

right.

11. Locate the area where the brake cable

attaches to the drive support. The beginning

adjustment should be

1.375 in.

of conduit

showing on the cable end.

Note: Spin the tire/wheel assembly to make sure

the brakes are not dragging with the brake pedal

NOT engaged.

12. Reinstall the electrical cables on the drive

motor.

13. Remove the jack stands and lower the

machine.

14. Reconnect the battery cables.

15. Operate the machine and check for proper

operation. Check the brakes for proper

operation. Adjust if necessary. See TO

ADJUST SERVICE BRAKES instructions.

Содержание 6200E































































































































































































































Результаты поиска

Содержание 6200E

Отзывы:

Tennant 6200E, Руководство по обслуживанию, Страница: 38 / 222

Результаты поиска

Содержание 6200E

Отзывы: