Tennant 6200E Скачать руководство пользователя страница 55

Страница: 55 / 222

CHASSIS

2-37

6200E 330415 (6--99)

TO REPLACE FRONT DRIVE ASSEMBLY

OUTER WHEEL BEARING

FOR SAFETY: Before Leaving Or

Servicing Machine; Stop On Level

Surface, Set Parking Brake.

1. Raise the seat support and unplug the

battery connectors.

2. Raise the front of the machine and place

jack stands under the frame.

3. Go to the side of the drive assembly

opposite the drive motor and remove the

hub cap. This will expose the outer bearing,

hex sleeve, and lock bolt.

4. Remove the lock bolt.

(this is a right--hand thread screw).

5. Remove the hex sleeve and outer bearing

cone assembly.

(this is a left hand thread nut).

6. Use a press to remove the old outer bearing

cone from the hex sleeve. Install a new

outer bearing on the hex sleeve or replace

the bearing and sleeve assembly. Apply

grease to the new bearing.

Содержание 6200E































































































































































































































Результаты поиска

Содержание 6200E

Отзывы:

Tennant 6200E, Руководство по обслуживанию, Страница: 55 / 222

Результаты поиска

Содержание 6200E

Отзывы: