SystemAir REPT10, Руководство по эксплуатации

Страница: 17 / 67

7 Base setup
7.1 Jumper for the input signal
The internal connectors are factory set for input
“
E1
”
in the position for a 0 - 10 V input signal and for input
“
E2
”
for a
temperature sensor
“
TF.
”
.
On sensors with different signals, the internal connector must be set to the correct position.
Attention
–
this must be done when the power is disconnected. Observe safety information! When using
“
sensors from
other manufacturers
”
, the connector must be adjusted according to the signal. The measuring range is adjusted in the
basic settings for the operating mode.
E1 Analog In (factory setting 0 - 10 V)
A
E1 GND
0-10 V
10 k
0 - 10 V TF..
24V
E1 GND
DSG 0 - 10 V
YE
DSG..
(0 - 10 V)
WH BN
24V E1 GND
MAL 0 - 10 V
3
MAL1/10
(0 - 10 V)
2 1
3 1
BN GN
MBG..-I
24V E1
MBG..
(4 - 20 mA)
E1 GND
TF..
03.02.2012
v_stecker_e1.vsd
E1.2 E1.1
0 - 10 V
E1.2 E1.1
0 - 10 V
E1.2 E1.1
0 - 10 V
E1.2 E1.1
4 - 20 mA
(0 - 20 mA)
E1.2 E1.1
TF.. (KTY)
E2 Analog In for operating modes with
2 sensors (factory setting TF..)
22.01.2008
v_stecker_e2.vsd
TF..
3 1
BN GN
MBG..-I
24V
E2
MBG..
(4 - 20 mA)
E2
GND
TF..
E2.2 E2.1
4 - 20 mA
(0 - 20 mA)
E2.2 E2.1
TF.. (KTY)
7.1.1 External Setpoint / External speed setting in manual operation
External Setpoint or external manual operation is possible by 0 - 10 V (0 - 20 mA, 4 - 20 mA) Signal at terminals “ E2 ” and
“ GND ” . Place internal Jumper “ E2.1 ” and “ E2.2 ” for “ E2 Analog In ” in correct position. “ E2 ” Con fi guration in base setup. For
Potentiometer Analog Out1 (terminal “ A ” ) program to function
|
1A
|
= “ +10 V ” (like factory setting IO Setup). If a second
sensor is connected at input 2, external Setpoint or speed setting in manual operation is possible with additional modul “ Z-
Modul-B ” (input E3 IO Setup).
E2 Analog In = 0 - 10 V
A
E2 GND
0-10 V
Analog In 2
02.12.2009
v_extern_stecker_v.vsd
E2.2 E2.1
10 k
E2 Analog In = 0 - 20 mA / 4 - 20 mA
E2.2 E2.1
Analog In 2
24.01.2008
v_extern_stecker_a.vsd
External Setpoint
via external signal instead of “ Setpoint 1 ” . The “ external Setpoint ” function must be activated in base setup
|
1E
|
for “ E2 function ” . The active external Setpoint value is displayed in the “ info ” menu group.
External speed setting
in manual operation. The “ external manual operation ” function must be activated in the basic settings
|
2E
|
for “ E2 function ” . Switchover between settings on the device and external manual operation via the digital input ( IO
Setup: “ Control / manual operation ”
|
7D
|
).
Operating Instructions
REPT6 / REPT10
Base setup
L-BAL-E081-GB 1237 Index 002 Part.-No. 00163316-GB
17/67