SystemAir REPT10, Руководство по эксплуатации

Страница: 49 / 67

Contact e.g. at ditgital input
“
Digital In 1
”
(depending on device type at terminals
“
D1
”
-
“
D1
”
or
“
D1
”
-
“ 24 V ” ).
Controller
1 0
n = 0 – 100 %
- - - - -
- - - - -
Sensor
11.05.2007
v_5d_sollwert_1_2.vsd
2
1
24V
D1 D1
1 Setting “ Setpoint1 ”
2 Setting “ Setpoint2 ”
• “ D1 Inverting ”
=
“ OFF ”
:
“ Setpoint1 ”
=
18 ° C at opened contact /
“ Setpoint2 ”
=
25 ° C at closed contact.
• “ D1 Inverting ”
=
“ ON ”
:
“ Setpoint1 ”
= 18
° C at closed contact /
“ Setpoint2 ”
= 25
° C at opened contact.
E1 Actual
Operation with “ Setpoint2 ” is signalized by the moon symbol for reduced operation.
9.9.3.7 Intern / Extern Function
|
6D
|
Switch over between Set Intern and Set Extern
(for mode speed controller
1.01
). “ Set extern1 ”
under settings must be programmed to “ OFF ” .
Contact e.g. at ditgital input “ Digital In 1 ” (depending on device type at terminals “ D1 ” - “ D1 ” or “ D1 ” -
“ 24 V ” ).
Controller
24V
D1 D1
1 0
n = 40 %
n = 80 %
Si 40 %
- - - - -
E1
11.05.2007
v_6d_vorgabe_intern_extern.vsd
1
0
1
Si Signal
1 Setting “ Set Intern1 ” (depending on device type in: %, Hz, rpm)
• “ D1 Inverting ”
=
“ OFF ”
:
“ Set Intern1 ”
at
opened contact /
“ Setting Extern ”
at
closed contact.
• “ D1 Inverting ”
=
“ ON ”
:
“ Set Intern1 ”
at
closed contact /
“ Set Extern ”
at opened
contact.
“
Setpoint1
”
/
“
external Setpoint
” (modes
2.01
)
Under Base setup “ E2 function ” programmed to function
|
1E
|
for “ external setpoint ” .
Contact at digital input e.g. “ Digital In 1 ” = “ D1 ” - “ D1 ”
Controller
24V
D1 D1
1 0
n = 0 – 100 %
- - - - -
Se
ES E2
26.05.2010
v_6d_sollwert1_externer_sollwert.vsd
1
1 Setting “ Setpoint1 ”
ES External Setpoint e.g. 5 V 23.8 ° C
Se Sensor
• “ D1 Inverting ”
=
“ ON ”
: Setting at the unit
at opened contact / Signal Extern at
closed contact
• “ D1 Inverting ”
=
“ OFF ”
: Setting at the
unit at closed contact / Signal Extern at
opened contact
9.9.3.8 Automatic control / speed manual, Function
|
7D
|
(mode
2.01
)
Switch over between automatic control to set target value (depending on the activation: “ Setpoint1 ” ,
“ Setpoint2 ” ) and the default for “ manual operation ” set at the device.
If for Analog In 2 “ E2 function ” is programmed to
|
2E
|
switch over between “ Setpoint1 ” or “ Setpoint2 ”
and external manual operation. With activated manual mode the display constantly changes between
“ actual value ” and value for “ manual mode ” .
Contact at digital input e.g. “ Digital In 1 ”
Operating Instructions
REPT6 / REPT10
Programming
L-BAL-E081-GB 1237 Index 002 Part.-No. 00163316-GB
49/67