SystemAir REPT10 Скачать руководство пользователя страница 61

Страница: 61 / 67

Status digital input 2 (Digital In 2)
OFF = terminals D2 - D2 bridged

↔

ON = terminals D2 - D2 not bridged

Status digital input 3 (Digital In 3*)
OFF = terminals D3 - GND bridged

↔

ON = terminals D3 - GND not bridged

Status digital input 4 (Digital In 4*)
OFF = terminals D4 - GND bridged

↔

ON = terminals D4 - GND not bridged

Status digital input 5 (Digital In 5*) OFF = terminals D5 - GND bridged

↔

ON =

terminals D5 - GND not bridged

OFF = relay K1 de-energized: terminals 11 - 12 bridged
ON = relay K1 energized: terminals 11 - 14 bridged

OFF = relay K2 de-energized: terminals 21 - 22 bridged
ON = relay K2 energized: terminals 21 - 24 bridged

OFF = relay K3* de-energized: terminals 31 - 32 bridged
ON = relay K3* energized: terminals 31 - 34 bridged

OFF = relay K4* de-energized: terminals 41 - 42 bridged
ON = relay K4* energized: terminals 41 - 44 bridged

* When operating together with the

“

Z-Modul-B

”

type expansion module, the diagnosis menu is

automatically expanded to include the additional inputs and outputs.

Events / Fault signals

11.1

Display and query of events and malfunctions

Events

Events during operation can lead to a malfunctioning of the device.
The last 10 (0 - 9) events and malfunctions are stored in the

“

Events

”

menu group

(position

“

”

= most recent event).

Essemple for possible
events

The device differentiates between 3 types of events:

Sensor 1

1. Messages with code

Msg

Message sensor fault for information, for Alarm sensor

deactivated.

External error

2. Alarms with code

Events during which the device automatically restarts

operation after the cause of the malfunction has been remedied (e.g. mains failure), or
remains in operation (e.g. externally-trunked centralized fault).

Motor fault

3. Error with code

Err

Events that lead to a disconnection of the controlled output

(e.g. excess motor temperature). Restarting is only possible after a reset (locked).

Operating Instructions

REPT6 / REPT10

Events / Fault signals

L-BAL-E081-GB 1237 Index 002

Part.-No. 00163316-GB

61/67

Содержание REPT10




































































Результаты поиска

Содержание REPT10

Отзывы:

Похожие инструкции для REPT10

Бренды по названию

Популярные бренды

SystemAir REPT10, Руководство по эксплуатации

Результаты поиска

Содержание REPT10

Отзывы:

Похожие инструкции для REPT10

Бренды по названию

Популярные бренды