Vista 5 M3 Digital Mixing System
4-124 GC Operation
Document generated: 28.08.13
SW V4.9
Speaker Calibration
To allow access to the speaker calibration, the Enable Setup function must
be enabled. Please refer to
chapter 4.7.5
.
Calibrate Mode
Calibrate mode allows setting a level offset for a whole monitor group
(
MAIN
,
ALT
or
NEARFIELD
) relative to the other two. To activate this mode,
click the ‘Calibrate’ button and select a monitor group on the control surface
monitoring section. The offset range is from –20 dB to +10 dB. The current
calibration offset will be displayed in the display box. The calibration offset
can be changed in steps of ¼ dB.
Trim Mode
Trim mode allows setting an offset for a single loudspeaker relative to others
in a group. The offset range is ±10 dB. Trim mode is selected by clicking the
‘Trim’ button. Select the monitor group (
MAIN
,
ALT
or
NEARFIELD
) and
SOLO
the speaker to be offset on the on the control surface monitoring section. The
current Trim value of the selected speaker will be displayed in the window.
The Trim offset can be changed in steps of ¼ dB. To clear all Trim offsets
within the selected monitor group, click the ‘TrimReset’ button.
Misc (-cellaneous Settings)
• The MUTE key may be disabled whenever the console is in ‘On Air’ (live)
mode.
• The state of sending the alternate n-x signal instead of the regular one may
be restored after opening and closing the fader.
• If the broadcast PFL mode (also referred to as ‘PFL cut on channel active’
function) is enabled, audio signals are cut from the PFL bus if the channel
is ON and the fader is open; the channel will also go back into PFL state
when the fader is closed again.
• If ‘Set Auxiliaries post Channel Mute’ is selected, all auxiliary busses are
muted if the channel MUTE key is activated. If this option is not active
(default), only the auxiliary busses switched to post-fader are muted upon
channel mute.
• The n-x signal output metering may be disabled.
• For controlling a DAW, either the Mackie HUI protocol or the Mackie
Control Protocol can be selected. If ticked here, HUI is active.
(Graphic EQ) View
When the 30-band graphic EQ is switched to the faders of a 32-fader con-
sole, all faders except the two control bay master faders are used anyway.
For 42-fader consoles however, it can be defined here in which fader bay the
leftmost EQ band is represented.
Содержание Vista 5 M3
