30
NeoCon Controller
[About the modal information absolute address A (angle of rotation)]
● Set the process start point to “0” and 0~359.999 which is within one rotation.
● If a value exceeding 360 is set to the address A by program communication, 『Err 114 ANGLE ERROR IN ABS
(angle error at the time of absolute command)』alarm will be triggered at the program run.
● For a setting out of the setting range, 『Err 309 PROG A ERROR (program A address input error)』
error will be triggered.
[About the modal information incremental address A (angle of rotation)]
● At the present position, set ±999.999 as the relative angle of rotation.
● Unless the address J is commanded separately, the address A is the address that must be set up.
● For a setting out of the setting range, 『Err 309 PROG A ERROR (program A address input error) at effective
continuous buffer (G08)』 error will be triggered.
[About the Address F (Rotation Speed)]
● If F is not set, the feed rate set up in the previous program will be applied as the modal information. However,
if no program which has been set up with feed rate has been executed before the execution block,
『Err 110 F DATA ERROR (feed rate data error)』 alarm will be triggered.
● If “F0” was set, the rotatin sped will be the same as the setting in the Pn002 (operation speed). However,
override is effective during automatic operation. If the override is set with a value other than 100%, the AUTO
mode LED will blink. If the override is set MAX or higher than the speed setting in the PRM 002, the upper limit
clamping will be activated at the speed of Pn002.
[About the Address D (No. of Equal Partition)]
● If D was not set up, or set to “0” or “1” normal positioning operation is started, as there is no partition.
● If the relation between the A command and D comand is A/D <Min. Feed Unit (0.001 deg),
『Err 107 DEVICE CMD ERROR (device command error)』 will be triggered.
● If address D was set up for the same position as the present position when the modal information is absolute,
the Rotary Table does not move at program statrt.
[About the Address J (Jump)]
● If no J setting, finish the block and proceed to the next block.
● If J is set up with block No., jump to the next block in the order after finishing the present block.
● If “J-1” is set in the program prior to the sub-program, return to the main program.
Explanation
[모달 정보 앱솔루트 어드레스A(회전각도)에 관해서]
● 가공원점위치를 “0”으로 하고 1회전 이내의 0~359.999의 값으로 설정합니다.
● 프로그램 통신에 의해 어드레스 A에 360 이상의 값이 설정된 경우에는 프로그램 실행시에 『Err114 ANGLE ERROR IN
ABS (앱솔루트 지령시 각도 에러)』의 알람이 발생합니다.
● 설정범위를 넘는 설정을 행한 경우 『Err309 PROG A ERROR(프로그램 A어드레스 입력 에러)』의 알람이 발생합니다.
[모달 정보 인클리멘탈 어드레스A(회전각도)에관해서]
● 현재 위치에서 상대적인 회전 각도를 ±999.999의 값으로 설정합니다.
● 어드레스J가 단독으로 지령되지 않는 한 어드레스A는 필수설정 어드레스입니다.
● 설정범위를 넘는 설정을 한 경우 『Err309 PROG A ERROR(프로그램 A어드레스 입력 에러) 연속버퍼 유효시(G08)에』의 알
람이 발생합니다.
[어드레스F(회전속도)에 관하여]
● F의 설정이 없는 경우에는 앞 프로그램에서 설정되어 있는 회전속도를 모달 정보로서 계속합니다.
단, 실행 블록 이전에 한번도 회전속도가 설정된 프로그램 실행을 하지 않은 경우에는 『Err110 F DATA ERROR(회전속도
데이터 에러)』 의 알람이 발생합니다.
●“F0”의 설정시에는, Pn002(고속속도)의 설정속도로 회전합니다.
단, 자동운전 중에는 오버라이드가 유효합니다.
오버라이드가 MAX 또는 Pn002의 설정속도보다 큰 경우에는 Pn002의 속도에서 상한 고정됩니다.
[어드레스D(등분할수)에 관하여)
● D의 설정이 없는 경우 또는 “0”이나 “1”이 설정된 때에는 분할 없음으로서 통상의 위치결정 동작을 실시합니다.
● A지령과 D지령의 관계가 A/D < 최소이동단위(0.001deg)인 경우에는 『Err107 DEVICE CMD ERROR(디바이스 지령 에러)』
가 발생합니다.
● 모달 정보가 앱솔루트시에 현재 위치와 동일 위치에 대하여 어드레스D를 설정한 경우에는 프로그램 실행시에 로터리테이블
은 동작하지 않습니다.
[어드레스J(점프)에 관하여]
● J의 설정이 없는 경우 블록 완료 후 다음 블록으로 진행합니다.
● J에 블록번호설정이 되어 있는 경우는 블록완료 후 지정 블록 번호로 블록 점프합니다.
● 서브프로그램 앞에서의 프로그램내에 “J-1”이 설정되어 있는 경우에는 메인 프로그램 리턴 복귀합니다.
해설
Содержание NeoCon Series
