91
Instruction Manual
Parameter
파라미터
파라미터의 할당은 기계원점위치를 기준으로 하여 시계방향으로 15°구획마다 되어 있고 다음과 같습니다.
파라미터 설정은 기계원점에 대응하는 피치 오차보정용의 데이터차(실측치-이론치)를 설정합니다.
Parameters are assigned to the sections of the table divided by 15°in CW, as follows.
The parameters set the deviation data (measurement - theoretical value) for the correction
of the pitch error to the machine start point.
MZERO
PITCH ERROR No.
0.0
45.0
90.0
270.0
315.0
180.0
215.0
135.0
(1) (2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(23) (24)
(22)
(21)
(20)
(19)
(18)
(17)
(16)
(15)
(14)
(13) (12)
(11)
(10)
기계원점위치
Machine start point pitch
Offset No.
Pn No.
Offset No.
Pn No.
(1)
Pn203
(13)
Pn215
(2)
Pn204
(14)
Pn216
(3)
Pn205
(15)
Pn217
(4)
Pn206
(16)
Pn218
(5)
Pn207
(17)
Pn219
(6)
Pn208
(18)
Pn220
(7)
Pn209
(19)
Pn221
(8)
Pn210
(20)
Pn222
(9)
Pn211
(21)
Pn223
(10)
Pn212
(22)
Pn224
(11)
Pn213
(23)
Pn225
(12)
Pn214
(24)
Pn226
9. 피치오차보정
9. Pitch Error Correction
피치 오차보정 데이터를 설정하는 것으로 대칭축에 대하여 0.001°단위로 피치오차를 보정할 수 있습니다.
기계원점위치를 보정의 기준각도로 하여 일정간격(15°) 마다 피치 오차보정을 설정할 수 있습니다.
This function sets up the pitch error correction data. Pitch error can be corrected by 0.001°unit to symmetrical shaft.
With the machine origin as the reference position of the correction, the pitch correction can be set up at 15°intervals.
피치 오차보정은 로터리테이블 1회전을 24분할하고 15°마다의 구획에서 순차적으로 파라미터가 할당되어 있고,
보정이 필요한 구획의 파라미터에 대하여 보정치를 설정합니다
For the pitch correction, the Rotary Table is divided into 24 sections by 15°and each partition is assigned with
parameter in sequential order. Correction values are set for the parameters of the section which require correction.
9.1 개요
9.1 Overview
9.2 파라미터 설정
9.2 Parameter Setting
Содержание NeoCon Series
