54
NeoCon Controller
N051
N051
N051
N050
N050
N050(N001)
N000
N002
Start point
WZERO POS
1st repeating
2nd repeating
3rd repeating
※ 상기 프로그램의 경우 G27지령에 대한 루프는 N050~N051입니다.
※ In case of the above program, the loop corresponding to the G27 command is N050~ N051.
프로그램
Program
내용
Description
N000 G24
가공원점복귀
Process start point return
N001 G27 S50 E51 R3
G27지령에서 N050~N051 블록을 3회 반복 실행한 후 N002로 이
행합니다.
In G27 command, repeat N050~N051 blocks for 3 times
and to go N002.
N002 G24
가공원점복귀
Process start point return
N050 A20.000 F0
회전속도는 고속으로 20° 계산
Speed of rotation is controlled feed, 20° calculation
N051 A40.000
회전속도는 고속으로 40° 계산
Speed of rotation is controlled feed, 40° calculation
프로그램 예
Examples
of Program
4.5.13 G90/G91 (앱솔루트/ 인클리멘탈)
4.5.13 G90/G91(Absolute/Incremental)
앱솔루트지령(G90)은 가공원점위치를 기준으로 하여 절대좌표를 설정합니다.
인클리멘탈지령(G91)은 현재위치를 기준으로 하여 상대좌표를 설정합니다.
G90, G91은 모달지령이므로 반대 지령(G90⇔G91)이 실시되지 않는 한 연속적으로 계속됩니다.
전원투입 후는 인클리멘탈지령(G91) 상태로 설정됩니다.
앱솔루트지령(G90) 시에 동일 좌표치를 지정한 경우에는, 이동동작은 하지 않고 블록완료(BLKFIN)를 출력합니다.
단, Pn103(일방향 위치결정)를 설정하고 있는 경우에는 일방향 위치결정 동작을 실시합니다.
The absolute command (G90) sets absolute coordinates system with the process starting point as the origin.
The incremental command (G91) sets relative coordinates system with the current position as the origin.
Since the G90 and G91 commands are modal commands, they are continued unless the opposite command
(G90⇔G91) is executed. After power on, the setting changes to the incremental command (G91) status. If the
same coordinates were assigned in absolute command (G90), no movement is carried out and BLKFIN is
outputted. However, is PRM 103 (unidirectional positioning) has been being set-up, unidirectional positioning
operation is carried out.
Содержание NeoCon Series
