45
Instruction Manual
4.5.8 G22 (연속스타트)
4.5.8 G22 (Continuous Start)
연속스타트 지령시(G22)에 지정된“회전방향”,“회전속도”에 의해 ST신호입력에서 회전 개시하고 다음 ST신호에서 정지합니다.
이 때 블록완료(BLKFIN)출력은 최초의 스타트용 ST시에 1회, 정지시의 ST시에 1회 출력됩니다.
G22지령에 대하여 어드레스 A, F를 지정하지 않을 경우에는 Pn037, Pn038에 의해 회전방향 회전속도가 결정됩니다.
By the direction of rotation and feed rate specified in the continuous start command (G22), rotation starts at the STSignal input and
stops at the next ST signal. Here, the BLKFIN output will be provided once at the ST for the first start and once at stopping. If ad-
dresses A and F were designated for the G22 command, Pn037 and Pn038 determines the direction of rotation and feed rate.
[어드레스A(회전각도)에 관하여]
● 회전방향은 “0”, 또는 “-0”으로 설정합니다.
0 : 테이블은 CW 방향으로 회전합니다.
-0 : 테이블은 CCW 방향으로 회전합니다.
● 어드레스A는 생략가능 하지만 생략된 경우에는 초기값 ‘0’으로 설정되어 CW 방향으로 회전합니다.
[어드레스F(회전속도)에 관하여]
● 어드레스F는 생략가능 하지만 생략된 경우에는 Pn038에 설정된 회전속도로 회전합니다.
[어드레스J(점프)에 관하여]
● 『G코드 없는 타입(표준)』참조.
[About the Address A (Angle of Rotation)]
● Set up the Speed of Rotation to “0” or “-0.”
0: The table rotates CW direction.
-0: The table rotates CCW direction.
● Though the Address A is omissible, however, if omitted, it is set to the initial value ‘0’ and the table rotates CW.
[About the Address F (Speed of Rotation)]
● Though the Address F is omissible, however, if omitted, the table rotates at the speed set up by Pn038.
[About the Address J (Jump)]
● See『Type without G Code (Standard)』
해설
Explanation
[프로그램 포맷]
G22
A_F_J_
굵은선 비스듬한 문자부분은 생략가능을 나타냅니다
G22 : 연속스타트 지령
A
: 회전각도
설정범위
: 0, -0
F
: 회전속도
설정단위
: 0.01min
-1
설정범위
: 0~9999
J
: 프로그램점프 대상
설정범위
: -1,0~999
J-1
: 서브프로그램 리턴지령
[Program Format]
G22
A_F_J_
Thick Italic letters represent the omissible parts.
G22 : Continuous start command
A
: Angle of rotation
Setting range : 0, -0
F
: Speed of rotation
Setting unit
: 0.01min
-1
Setting range : 0~9999
J
: Object of program jump
Setting range : -1,0~999
J-1
: Subprogram return command
Содержание NeoCon Series
