96
NeoCon Controller
11. 오버트레벨
11. Over Travel
오버트레벨(OT)의 +측, -측의 판정은 OT 검출시의 동작방향에 의해 결정합니다.
그러므로 알람검출 후에 리셋을 실시하면 알람은 일시 해제되고 다음 동작 시에 다시 알람이 발생합니다.
The + or - side of the over travel (OT) is determined by the direction of motion at the OT detection.
Therefore, if reset after an alarm detection, the alarm will be reset temporarily and then triggered again
at the next movement.
파라미터설정
Parameter
setting
오버트레벨 검출을 한 경우의 파라미터는 다음의 종류로 설정합니다.
Pn107=1 (시리얼 검출방식)
Pn202=1 (OVRUN의 접점사양을 B접점으로 실시)
When over travel is detected, the parameters are set up as follows.
Pn107=1 (Serial Detection Method)
Pn202=1 (contact type of OVRUN is B type contact point)
시리얼 검출방식
Serial Detection Method
OT 검출
OT Detection
오버트레벨 1검출 중에 +회전을 하고 있거나 또는 한 경우에는 『Err.011 OVER 』의 알람이 발생하고 다이나
믹 브레이크에 의해 긴급정지 합니다. 또한 오버트레벨 1검출 중에 -회전을 하고 있거나 또는 한 경우에는『Err.012 OVER
TRAVEL -』의 알람이 발생하고 마찬가지로 다이나믹 브레이크로 긴급 정지합니다.
OT검출 중에 전원 차단한 경우에는 최초의 동작에 따라 “Err.011”나 “Err.012”가 결정합니다.
그러므로 +측 위치에서의 OT검출 중에 [DEL]을 누르면 통상과는 반대로 『Err.012 OVER TRAVEL -』이 발생하고 -측 위
치에서의 OT검출 중에 [INS]를 누르면 통상과는 반대로 『Err.011 OVER 』이 발생하므로 오버트레벨 해제동작
은 신중하게 해주십시오.
At the detection of over travel 1, if the table is rotating or has rotated in '+' direction,「Err.011 OVER 」
alarm is triggered and the table is stopped immediately by the dynamic brake. At the detection of over travel 1,
if the table is rotating or has rotated in '-' direction,「Err.012 OVER TRAVEL-」alarm is triggered and the table is
stopped immediately by the dynamic brake.
If power is cut off when OT is detected, 'Err.011' or 'Err.012' is determined according to the initial movement.
Opposite to the normal condition, if [DEL] is pressed when OT was detected in '+' side,「Err.012 OVER TRAVEL-」is
triggered or if [INS] is pressed when OT was detected in '-' side,「Err.011 OVER 」will be triggered.
Therefore, OT reset must be conducted carefully.
90.0
270.0
②
①
①
①
MZERO
-OT
(OVRUN1-2)
+OT
(OVRUN1-1)
Rotation
AVOID DIR
DNG DIR
Rotation
+
-
OVRUN1-1, 1-2를 시리얼 접속하고, OVRUN1에 입력
그림중 ①동작에서는『Err.011 OVER 』
그림중 ②동작에서는『Err.012 OVER TRAVEL -』 가 발생합니다.
In the figure, movement
① will trigger「Err.011 OVER 」and
② will trigger「Err.012 OVER TRAVEL-」.
Connect OVRN1-1 and 1-2 in serial,
and input into OVRUN1
Machine start point pitch
기계원점
Содержание NeoCon Series
